Can I Really Replace My Own Kitchen Faucet?
R. Dodge Woodson/Lone Wolf Enterprises, Ltd.
Can I Really Replace My Own Kitchen Faucet?
Can I Really Replace My Own Kitchen Faucet? If you have moderate mechanical ability and the right tools, you can certainly replace your old kitchen faucet with a new one. The one special tool that you should have is a basin wrench. This allows you to get to the mounting nuts and supply nuts. Without a basin wrench, the job is miserable. Hardware stores usually sell cheap basin wrenches that will work for less than $20. The other tools that come in handy are adjustable wrenches and water-pump pliers. A tubing cutter or a hacksaw may be needed in some cases. Some type of light, such as a flashlight, will come in handy. You should also obtain some stainless plumber’s putty and some pipe-thread sealant when you are at the store. It never hurts to pick up a couple of supply tubes in the event that your existing supplies don’t fit the new faucet. Ask for ferrules to use on the supply tubes for compression connections.
Now that you have an idea of what you will need for a typical replacement, let’s run through the procedure. I strongly suggest that you wear a pair of goggles or safety glasses when removing your old faucet. It is common for rust to fall from above and fill your face with nasty brown particles. You don’t want these in your eyes.
Your sink should have two cut-off valves under it. If not, don’t cut any piping. Turn off the cut-offs. Turn on the old faucet to confirm that the water is off. Lie under the sink and use the basin wrench to loosen the nuts that hold the supply tubes to the faucet. Then loosen the mounting nuts. Left is loose—right is tight. If the old faucet has a spray attachment, cut the hose. Remove the old faucet. You are left with the holes in your sink and the supply tubes waiting for the new faucet.
Read the installation instructions for your new faucet. Always follow the manufacturer’s recommendations. In the meantime, I will give you a quick rundown of what you will be doing. Most faucets are shipped with a rubber gasket that fits between the faucet and the top of the sink. If this is not the case, use stainless putty to seal the edges of the faucet. This is done by rolling the putty in your hand until you have enough to lay it along the outline of the faucet.
Place the faucet through the mounting holes and install the washers and mounting nuts. Check the faucet to make sure that it is in proper alignment before final tightening. Ideally, the existing supply tubes will fit right into the faucet receptors. When this is the case, you set the supply tubes, tighten the supply nuts, and turn on the water at the cut-off valves to see if you have any leaks.
If everything stays dry under the sink, remove the screw-on aerator from the faucet. This is the piece on the spout that water comes out of. You remove this to avoid getting debris in it when you first turn the faucet on. Turn the faucet on and see if all is working well. Once the water is running properly, turn it off and reinstall the aerator.
If the supply tubes are too long or too short, replace them with the spare supply tubes that you bought. They are cheap and make for good insurance. You will have to use the new ferrules to make your compression connection on the supply cut-offs. Loosen the nuts that hold the supply tubes into the cut-off valves and lift them out. Cut the supply tube to recover the nuts. Slide the nuts on the new supply tubes and then slide the ferrules over the supply tubes. Cut the tubes to a proper length and place them in the cut-off valve. Slide the ferrule down to the cut-off and secure the connection with the supply nut.
Replacing a faucet is not a big job when everything goes right. The key factor is to make sure that you have the water cut off before you disturb any plumbing. Stay dry, and enjoy your new faucet.
R. Dodge Woodson and his team at Lone Wolf Enterprises, Ltd. (www.lonewolfent.net) are offering their services to the open market for the first time. Woodson has written over 100 books for major publishers, such as Simon & Shuster, McGraw-Hill, John Wiley & Sons, and others. He is acknowledged as a best-selling, internationally-known author. R. Dodge Woodson got his start writing dozens of magazine articles for such magazines as Outdoor Life. In addition to his personal writing, Woodson?s team has produced dozens upon dozens of books for major publishers.
R. Dodge Woodson?s writing style is conversational. He is skilled at taking complex subjects and making them reader friendly. Woodson has worked as a ghostwriter for celebrities, provided work-for-hire books to major publishers, and written his own titles.
If you are seeking professional writing and editorial services, Lone Wolf can deliver all elements of publishing from writing to editing to layout to proofreading to indexing, and more.